If even after feeding the 5 V, does not work anything except button ANALOG, that now ignites the light , you will have to make a small modification in the connections. The most common problem is that it does not do anything. The other wire the black you solder to pin 18 or 19 or where it connected the wire that corresponds of hole 6. We are going to find out to what hole of the female connector is connected to which small wire. Well, we now have written on the paper the relation of the holes from the 1 to the 9 and to what cable color in the other end corresponds to each one of them.
|Date Added:||12 November 2017|
|File Size:||48.57 Mb|
|Operating Systems:||Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X|
|Price:||Free* [*Free Regsitration Required]|
If you want to see the complete list of games that support the Force Feedback, look here. If your controller doesn’t power up many racing controllers need more power than the parallel port can supply, eirectpad example you may want to try adding an external 5V power supply: If you do not have any idea, or don’t want to do it get a friend who knows to help you.
Take the female connector of the cable and put the pin in each one of the holes to make contact and, using the multi-meter on resistant setting, write down to what direftpad corresponds each wire of the other end. The interface is shown looking into the pad’s connector.
You can connect simultaneously up to two pads. Connecting a second PlayStation Pad to the same parallel port.
Win9X Direct Pad Pro 5 installation
Now cut each one of these wires except the one that does not have insulator that you can cut it directly removing little insulation from the ends of the wires so you have bare wire. Connect the 5v to pin 5 of the pad were the diodes connected and the ground to pins 18 and 19 of the DB connector.
Before beginning with the explanation I must make clear to you that I have not made the assembly. Look to the attached figure considering that the part that is seen in drawing is the part where we are going to solder.
Once connected everything it gives just as it is dual-shock or notwe verified in the configuration of the driver none of the buttons nor any directional ones work. Make sure the colors are the same.
And it is ready. Remember that you must weld the 5 diodes in the correct direction.
In theory if first pad works the second would have to also work perfectly. Make sure that the voltage is 9v using a milti-meter. Be aware that this interface is different from SnesKey’s interface. The other wire the black you solder to pin 18 or 19 or where it connected the wire that corresponds of hole 6. After making sure all the connections are correct you did this first didn’t you?
Connect it to dircetpad 5 of the pads.
Take the extension cord and cut the cable shortly before arriving at the end where the male connector is connected. The only solution that I know is to enter way of failures on approval F8 when starting windowsto deselect that driver and to prove conflict with another one.
Maybe except to Calibrate the controller. For me I had to click Add Before starting, we are going to make sure that you have a free power connector. Following with the preliminaries, I will going to make clear that you do not need any knowledge electronics, although knowing how to solder and know how to handle a multi-meter.
Direct Pad Pro – Joystick Emulators – Zophar’s Domain
We are going to find out to what hole of the female connector is connected to which small wire. If you have a dual-shock compatible pad make sure it has 8 wires. In this case you can buy an accessory that makes two connectors from one single one, y-adapter but you risk to overload the power supply unlikely. Before executing the game enter game configuration and select it in Properties of driver. Get the newest DirectPad drivers of here and unzip it to a temp directory anywhere, ei.
Well, we now have written on the paper the relation of the holes from the 1 to the 9 and to what cable color in the other end corresponds prro each one of them. If you pay attention, hole 6 driectpad the female connector must go connected to pins 18 and 19 of connector DB The wire that corresponds to hole 5 of the connector you have it to weld to the other ends of the 5 diodes.
It seems that some problems with the assembly exist aint this always the case?